Honest Hunter’s

February 9, 2017

Its time to start a new project!

This year I will be working on stock removal hunting style knives. The first batch of twelve will be what I call “Honest Hunter’s, because honestly that’s what they are 🙂

These first prototype’s will be cut from Aldo Bruno’s 1084 1/4″ bar stock, profiled, shaped and heat treated in house. The handles will be carved from good old g-10 and they will have 3/16” Corby Bolts.

I will be posting progress pictures along the way.

Enjoy,

 

Bobby

 

 

16114531_10210661829375045_4563802485246006615_n.jpg

16174470_10210661828695028_5645644264823062616_n.jpg

Check out the sleek profile in the two pictures above

 

16195013_10210661839575300_7665236549908977983_n.jpg16113881_10210661840975335_5837813632527668532_n.jpg

All of the blades have been sprayed with layout fluid to ensure precise alignment of holes

16114801_10210661847455497_4728777634101366214_n.jpg16265926_10210661847415496_5725765255921962453_n.jpg

At this point I use my vertical height marking gauge to layout the center point of each blade. This will help ensure consistency on all of my bevel grinds.

 

16143318_10210661847775505_5124477155713274774_n.jpg

Note: I mark two lines approximately .030 apart, because that’s how thick I want the blade to be prior to heat treating.  

 

16406596_10210726238825241_8598143192263230710_n.jpg

The weight reduction holes are all laid out

16299339_10210726238905243_5091980876770940398_n.jpg

Now all of those holes are drilled out

16406581_10210726238865242_7635442093045139455_n.jpg

Consistency is key, once a template is created … transfer punches are used to replicate exact hole locations.

Note: I lay the template over each blank and clamp her tight. 

16298602_10210729552148072_7117359184939675714_n.jpg

 

16387946_10210729552188073_8104985786913828230_n.jpg

Ready for the grinder

 

16472949_10210787502236788_7975082959637562213_n.jpg

Plunging right into it 🙂

 

16508896_10210781285121364_452034622666224853_n.jpg

 

16427466_10210781285001361_283685382946892703_n.jpg

Moving right along with the bevels

hol.jpg

Hollowing out the tangs for additional weight reduction

 

16508492_10210789733172560_4873000290264726460_n.jpg

Ready to be normalized … all that drilling and grinding has disrupted the carbon and other molecules … normalizing the blades will help ensure a successful heat treat.

Basically, I heat the blades to 1550 degrees and let them cool at room temperature until all of the color disappears and they are basically grayish black in color. I’ll do this twice. Then I’ll do it again with a slightly lower temperature, 1425 degrees to be exact.

 

IMG_0220.JPG

Sable & Cooper (aka the shop dogs) guarding the blades prior to normalization.

 

IMG_0229.JPG

Gotta love the Pargon Kiln

 

IMG_0232.JPG

Cooling down at room temp between cycles

 

IMG_0252.JPG

After the final normalizing cycle … the blades are heated past critical and quenched using my limiter plate for consistency.

 

IMG_0227.JPG

Now it relaxation time. Light up the finger lamps, get a little snack while the Pargon Kiln tempers the blades to around 59-61 RC.

 

IMG_0256.JPG

Time to finish grind these bad boys.

 

IMG_0261.JPG

Almost ready for some G-10 and Corby Bolts

 

IMG_0263.JPG

Sweet little Hunter’s coming to life.

 

16832271_10210937192178943_372994938079104129_n.jpg

16832306_10210937192258945_4928486452345534498_n.jpg

Wrap up the blades to protect them during handle work

 

IMG_0399.JPG

G-10 Scales all ready to go

 

IMG_0400.JPG

Making Dust … always wear your respirator!

 

IMG_0424.JPG

Add some Corby Bolts

 

IMG_0430.JPG

Breakfast in the Shop

 

IMG_0429.JPG

Man that bacon smells good!

IMG_0427.JPG

 

IMG_0428.JPG

Shop Dogs … Cooper (14 years old) & Sable (15 years old)

 

IMG_0438.JPG

IMG_0439.JPG

All Epoxied Up!

 

IMG_0483.JPG

 

IMG_0445.JPG

IMG_0448.JPG

IMG_0449.JPG

 

IMG_0480.JPG

 

IMG_0481.JPG

 

IMG_0482.JPG

Off the grinder and ready for a little hand work before headed to my father-in-law Paul Wittle for sheaths.

 

IMG_0509.JPG

IMG_0510.JPG

 

 

 

 

Advertisements

My JS Blades

June 27, 2015

My JS Test Knives

My JS Test Knives

These pieces are currently having sheaths made and will be posted for sale soon!

If you are interested in a particular knife, email me and I’ll hold it for you.

 

Thanks for looking,

 

Bobby

2010 Archery Contest Knife

August 22, 2010

Hi Everyone,

Below you will find pictures of the 2010 Archery Contest Knife…A.K.A. “The Camp Beast”. I call her the camp beast cause she’s a big old Bowie, Fighter styled camp blade that can handle most any choir around. Specs are as follows:

10″ blade of 5160 triple tempered

walnut handle with cold blue fittings and checkered spacer

O.A.L. is 15 1/2″

Thanks for looking,

Bob

Long Clip Hunter

February 13, 2010

Hi Folks,

Just finished this knife for a customer….with an extra long clip on cold blued blade of 1095 edge quenched steel. The blade itself measures 4 5/8″ with an O.A.L. of 10″. The customer supplied the wood…African Rosewood aka Bubinga…it’s beautifully grained with streaks of brown, black, and orange. Nickel silver fittings include a guard, butt cap, pommel nut, an a single 1/16″ lightly domed pin. There is a cold blued mild steel spacer behind the guard to balance out the blade.

Thanks for Looking,

Bob

This piece is sold!